River Table Casting Resin 750ml KIT

River Table Casting Resin 750ml KIT

gray stars

Comes with 500ml Resin and 250ml Hardener

 

Can be used anywhere a hard, durable, crystal clear coating is required. Excellent for casting and encapsulating. 

 

Easy MIX 2 Part A : 1 Part B (by volume) 

Can$67.95
SKU 27717

Features Include:

• Ideal 2:1 Mix Ratio

• Extremely Tough Surface

• High Gloss *Blush Resistant

•  Excellent adhesion to wood

• Can be poured up to 1.5" Thick for a single pour

 

How much resin do I need? CLICK HERE FOR RESIN CALCULATOR

Surface Preparation: To achieve excellent adhesion, the substrate must be free of all loose and foreign material and should be clean. Oils, Grease, waxes or other contaminates must be removed prior to coating.

Mixing: The storage temperature of River Table Casting Epoxy will greatly affect the ease of mixing, application and curing time. For best Results, should be stored at 70-80°F for at least 24  hours before use.

Mix 2 parts A (resin) to 1 part B (hardener) by volume using a spatula or stir stick until uniform. Be sure to scrape sides of the mixing container while mixing (any unmixed or partially mixed material will cause wet spots on finished surface) DO NOT mix more material than can be used withing the stated working time. REMEMBER - you will have less working time at higher temperatures. 

Application: River Table Casting Epoxy can be applied with a foam brush/roller or squeegee. Usually material is applied in stages with no pour thicker than 1.5 inches (unless casting can be cooled). recoats can be applied as soon as current layer has "tacked up". If your previous layer has fully cured then very light sanding with a fine grit (220) sandpaper followed by a solvent wipe(isopropyl alcohol or acetone) is necessary before application of subsequent layer. A heat gun or torch may be used after the pour is completed and the material is still liquid to burst/pop any remaining air bubbles. If a torch is used the flame should never come in direct contact with the epoxy, smooth strokes 6-12 inches above the material is all that is required. 

SAFETY PRECAUTIONS:

  • Mix and pour in a well-ventilated area.
  • Avoid contact with skin and eyes. If contact does occur, wash skin with soap and water and seek medical help.
  • Read and understand all CAUTIONS on container labels and safety data sheets before using this material.
  • Avoid breathing of vapors.
  • Forced local exhaust is recommended to effectively minimize exposure.
  • NIOSH approved, organic vapor respirators and forced exhaust are recommended in confined areas, or when conditions (such as heated polymers, sanding) may cause high vapor concentrations.

DO NOT WELD ON, BURN OR TORCH ON OR NEAR ANY EPOXY MATERIAL. HAZARDOUS VAPOR IS RELEASED WHEN AN EPOXY IS BURNED.

 


 Shipping Chemicals and  Wide Fabric Make it impossible to Calculate Shipping Costs in Advance.
Your trust is important so we only charge what shipping cost us.
 
Disclaimer: The information contained herein and provided by RAYPLEX LTD is considered accurate.
However, no warranty is expressed or implied regarding the accuracy of the data, the results to be obtained
by the use thereof, or that any such use will not infringe any patent. Before using, user shall determine
the suitability of the product for the intended use and user assumes all risk and liability whatsoever
in connection therewith.
 

CUSTOMER SERVICES

WEBSITE INFORMATION
RESOURCES

RAYPLEX LTD

Returns
Shipping 
Indian Status Tax Exemption

Education Discount Program

Copyright © 2024 Rayplex Ltd.  
RAYPLEX is a registered
Trade Mark All rights reserved. 
341 Durham Crt, Oshawa, ON L1J 1W8
Phone: 905-579-1433 Fax: 905-579-1431
Hours of Operation:
Mon-Thurs 9am-5pm
Fri  9am-4pm
Email: sales@fibreglass.com